Skip to content
Burlington Plumbing CompanyBurlington PlumbingCompany Call now(365) 464-5184
A pressure gauge mounted on a pipe

Pipe work

Low Water Pressure Repair in Burlington

Weak showers, a slow-filling tub or a dishwasher that complains about intake are symptoms. The cause is often a single valve, regulator or section of old pipe.

  • Leaks traced with meter and camera
  • Copper, PEX and press fittings
  • Pressure tested after repair
  • Drywall openings kept small
Call now(365) 464-5184

Calls only · a person answers

  • 24 hResponse
  • 28 areasAreas
  • 28 servicesServices
  • Licensed & insuredTrust

Signs it is time for low water pressure repair

Call when pressure has dropped gradually throughout the house, when one floor or fixture is much weaker than the rest, when hot water is slower than cold, or when pressure swings sharply during the day. A sudden drop everywhere may mean a city watermain break or a leak on your service line, so it is worth checking with neighbours first.

What's included

  • Moisture meter and thermal camera
  • Copper, PEX and press fittings
  • Pressure gauge on a hose bib
  • Tubing cutters and a torch

Our method on site

Measuring comes before guessing. We fit a gauge to a hose bib or laundry tap to read static pressure and watch how far it falls with fixtures open. Then we work back from the problem fixture:

  • Aerators and cartridges clogged with scale or debris.
  • The main shut-off, which on older gate valves can sit partly closed or have a detached gate.
  • The pressure-reducing valve, where one exists, which can fail low or drift.
  • Old galvanized pipe, narrowed inside by decades of corrosion.
  • The water heater, where sediment or a faulty inlet restricts hot flow only.

Tell-tale signs

  • A water bill that climbs with no change in use
  • Stains on a ceiling below a bathroom
  • Banging pipes or low pressure
  • Green or white crust on copper joints

What affects the scope

Some fixes take minutes: cleaning an aerator, opening a valve that was never fully reopened after a renovation. Others take more planning. Replacing a regulator is a short job; replacing a corroded galvanized branch means opening walls. Where the incoming service is the bottleneck, a water line replacement may be the only real cure. We show you the gauge readings so the recommendation makes sense.

Try first: take the aerator off a weak faucet, then turn it on. If flow jumps, the screen was the problem. If it stays weak, the restriction is further back.

Job at a glance

Work
Low Water Pressure Repair
Trade
Pipe work
Where
Burlington and nearby
Book
(365) 464-5184

Burlington homes and this job

Halton Region supplies water at pressures that vary by elevation and pressure zone, so homes near the escarpment and those close to the lake can read quite differently. Post-war houses in Dynes, Roseland and parts of Aldershot sometimes still carry galvanized steel branches, a frequent source of slowly declining flow. Newer homes are more likely to have PEX or copper, where a failing regulator or a scaled cartridge is the usual culprit. If a whole-house upgrade comes up, see repiping; if you are weighing an on-demand heater, low incoming pressure affects how a tankless water heater performs.

Water hardness plays a supporting role. Scale builds in showerheads and cartridges over a few years, so a slow decline in one bathroom often points there first.

Plumbing renovations can leave clues too. A new fixture fed by an undersized line, or a stop valve left half open after a vanity swap, explains many single-room complaints we trace.

Questions to ask

  • What was the static reading, and what does it drop to under use?
  • Is the problem on my side of the meter or the city's?
  • Is a full repipe necessary, or will one branch do?

Our low pressure guide walks through checks you can do first.

How the visit runs

  1. 1

    Close the main and drain down the line.

  2. 2

    Find the leak or weak section and open the access.

  3. 3

    Cut out the damaged pipe and fit new.

  4. 4

    Pressure test, restore water and check for weeps.

Questions we hear

Why is only my hot water pressure low?

Restrictions in the water heater, such as sediment or a partly closed inlet valve, or a faulty mixing cartridge are the usual reasons.

Can water pressure be too high?

Yes. Very high pressure stresses fixtures and appliances, and a pressure-reducing valve brings it to a safer range.

Does the city control my water pressure?

Halton Region sets supply pressure by zone. Inside your home, valves, pipes and regulators determine what reaches your fixtures.

Call now(365) 464-5184